Graco 2009669 Tube Polyethylene 1/4" O.D. replaces Graco 054118
$892.00
In Stock
Graco 2009669 Tube is a durable 1/4" O.D. polyethylene tube designed for low-pressure resin or catalyst fluid lines in Graco FRP and proportioner systems.
- Material: Polyethylene (PE)
- Outer Diameter: 1/4" (6.35 mm)
- Used in FRP Proportioners & Catalyst Kits
- Not for high-pressure spray lines
Quantity
Genuine OEM Part
Fast Shipping (Order by 1 PM CST)
Easy Returns
Graco 2009669 – Polyethylene Tube (1/4" O.D.) Overview
Compatible Machines & Systems
Graco 2009669 Tube is used in the internal, low-pressure fluid/catalyst circuits of the following Graco systems and kits (when 1/4" O.D. polyethylene tubing is specified):
- Graco FRP Proportioner (Gel Coat & Chop) systems – internal resin/catalyst plumbing per FRP manuals (3A2012 series).
- FRP Stainless Steel Catalyst Fitting Kit (manual 332451) – calls out 2009669 as 1/4" O.D. tube (5 ft).
- FRP 5-Gallon Catalyst Reservoir Kit 24M501 – parts list includes 2009669 tubing.
- 2K-WR Proportioner systems – internal low-pressure tubing noted in the 3A4527 manual.
- HB Fuller Liquamelt adhesive equipment systems (Graco documentation) – lists 2009669 tube as required part.
Quick Specifications
| Part Number | 2009669 |
|---|---|
| Description | Tube, Polyethylene, 1/4" O.D. (natural/PE) |
| Typical Length Referenced | 5 ft (1.5 m) in FRP kit listings (actual length used may vary by machine/section) |
| Typical Use | Low-pressure internal resin/catalyst routing, supply/return, reservoir plumbing |
| Material Compatibility | General compatibility with many resins/catalysts; confirm chemical compatibility for your fluid |
| Barcode / GTIN | 00769946893977 (where published) |
| Not For | High-pressure spray hose service; use only where 1/4" O.D. PE tube is specified |
Key Features & Benefits
- OEM Graco specification for machines/kits that call out 1/4" O.D. PE tube.
- Clean routing for catalyst/resin priming, returns, and reservoir plumbing.
- Cut-to-fit on installation—trim to exact run length required by your unit.
Fitment & Installation Notes
- Verify your unit specifies 1/4" O.D. polyethylene tubing at the connection points.
- Match with the correct compression/barb fittings and pipe sealant where required.
- For larger runs that specify 3/8" O.D. PE tube, Graco commonly references 054106 (not interchangeable).
- Always check fluid compatibility and observe the machine’s maximum working pressure rating for low-pressure lines.
What’s Included
- Graco 2009669 Tube, Polyethylene, 1/4" O.D. (quantity/length as ordered for your application)
Frequently Asked Questions
No. 2009669 is a polyethylene tube (1/4" O.D.) for low-pressure internal circuits (e.g., resin/catalyst supply/return). For high-pressure spray, use the correct Graco airless hose specified for your sprayer’s pressure rating.
It appears in parts lists for FRP Proportioner systems (3A2012 series), the FRP Stainless Steel Catalyst Fitting Kit (manual 332451), the FRP 5-Gallon Catalyst Reservoir Kit 24M501, certain 2K-WR Proportioner documents, and Graco documentation for Liquamelt adhesive equipment. Always verify against your exact model’s manual.
FRP kit references commonly show 5 ft (1.5 m) segments, but the actual run length depends on your machine’s routing. Measure your existing line and add a small margin for service loops and clean cuts.
Only substitute if your machine’s manual allows it. Changing material or O.D. (1/4") can affect sealing, chemical compatibility, and flow. For 3/8" O.D. runs, Graco often specifies 054106 instead.
Check the chemical compatibility of your resin/catalyst with polyethylene and follow your unit’s manual for approved materials and maximum working pressure. When in doubt, consult the machine’s spec sheet or contact Graco support.
No reviews yet. Be the first to review this product!
